Shop 24/7 at www.seawide.com 369 Rigging • MOTOR & DRIVE UNIT T-H Flex™ Sleeving Lightweight sleeving protects wire, cables and hoses. Braided from high temperature yarns and expands up to four times its normal diameter. (T9T) Bulkhead Strain Relief Hose Kit Distributes strain from bends in hose. Water tight and great for hydraulic steering hose. Flange is 2-3/4” diameter and requires 1-1/4” installation hole. Part No. BSR-1K-DP Protects cables and wiring from elements. Molded polypropylene ange is threaded to retain hose. Vinyl cap provides closure for the engine end of hose. Kit includes ange and 4’ of rigging hose in black or chrome. Rigging Flange, Hose & Kits Part No. Description RF-1-DP Black, 2” RF-2-DP White, 2” RF-2.5-1-DP Black, 2.5” RFH-1-DP 2” Rigging Hose, Black 50’ Roll RFH-2-DP 2” Rigging Hose, White 50’ Roll RFK-1CP-DP 2” Chrome Rigging Flange Kit Protects cables, hoses, and wiring from elements. Molded polypropylene threaded ange to retain hose. Kit includes rigging hose and ange. Rigging Hose Kit Part No. Description RFK-1-DP 4’ Hose & 2” Flange, Black Part No. Description 16700001X-DP 5.8-7.0, 10-Pack 16700004X-DP 7.8-9.5 10-Pack 16700006X-DP 8.8-10.5 10-Pack 16700007X-DP 9.6-11.3 10-Pack 16700010X-DP 10.8-13.3 10-Pack 16700012X-DP 11.5-14.0 10-Pack 16700013X-DP 12.0-14.5 10-Pack 16700016X-DP 13.2-15.7 10-Pack 16700017X-DP 14.5-17.0 10-Pack 16700020X-DP 15.3-18.5 10-Pack 16700024X-DP 17.8-21.0 10-Pack 16700031X-DP 22.4-25.6 10-Pack 16700037X-DP 26.9-30.1 10-Pack 16700040X-DP 28.4-31.6 10-Pack 16705989X-DP 37.8-41.0 10-Pack Stepless clamps are available in key sizes and offer uniform compression and increased clamping force. Oetiker Stepless Ear Hose Clamps Nylon Cable Ties High tensile strength, lightweight, exible made with nylon are non-corrosive cable ties. Easily support 50 lbs of force. Sizes ranging from 4”-14”. Part No. Description 075B-RAD-C-DP 7-1/2” Radiused Tie, Black 100/Pkg. 075B-RAD-M-DP 7-1/2” Radiused Tie, Black 1000/Pkg. Clam Shell Vent These super-strong molded clamshells are an economical and attractive alternative for metal clamshells. Use to route cables or wires through a hole or for covering thru-hull openings to shield water spray. Opening 9/16” H x 1 7/8” W. Base 2”x2”. Part No. Description CS-1-DP Black, Standard Vent CSS-1-DP Black, Small Vent Covers wire pass-thru holes. Provides a nished look for wiring. Wire Cover Part No. DWC-1-DP Provides a fully open area to pass wiring and cables through. Constructed of rugged black vinyl that resists ultraviolet rays, gasoline and oil. Cable Boots Part No. Description CB-1-DP 3” Cable Boot CB-2-DP 2” Cable Boot CB-4-DP 4-1/2” Cable Boot Reinforcing Cable Boot Rings Installs over the base ange of T-H Marine cable boots. Provides a neat and tidy trim. Reinforces the softer vinyl cable boot to protect it from pulling thru screws due to movement of cables. Part No. Description CBR-1-DP 3” Cable Boot Ring, Black CBR-2-DP 2” Cable Boot Ring, Black CBR-4-DP 4.5” Reinforced Cable Boot Ring, Black Part No. Description FLX-50-DP 1/2”, 100’ Spool FLX-75-DP 3/4”, 100’ Spool FLX-150-DP 1-1/2”, 50’ Spool Completes professional rigging installation and complies with ABYC-NMMA speci cations. Split design of union allows installation on pre-rigged boats. Fuel hose ports ID = 3/4”. Install with 2” ID T-H Marine rigging hose. Rigging Flange with Fuel Hose Port & Rigging Flange Hose Union Part No. Description RFFHP-1-DP Fuel Hose Port, Black RFHU-1-DP Rigging Flange Hose Union
RkJQdWJsaXNoZXIy MTAyMzU3Ng==