Shop 24/7 at www.seawide.com 367 Performance • MOTOR & DRIVE UNIT (T9T) Part No. SCM-2-DP Marine plywood reinforced wheel mount area made of welded aluminum. Adjustable height from 16” to 26”. Steering Console Mount Jack plate comes with relay harness and rocker switch. Contact your boat manufacturer for setback recommendation for your particular boat and also the affects adding a jack plate can have on your boat. NOTE: Mounting bolts are not included. Rated for engines up to 300hp or up to 625 pounds dry weight. Transom side of the atlas is 16-3/8” wide x 12- 1/2” tall. Setback Hydraulic Jack Plates Part No. Description AHJ-4V-B-DP 4” Gloss Black Anodized AHJ-4V-DP 4” Polished AHJ-4VHD-DP 4” Heavy Duty AHJM-4-DP 4” Micro AHJ-6V-B-DP 6” Gloss Black Anodized AHJ-6V-DP 6” Polished AHJ-6VHD-DP 6” Heavy Duty AHJ-8V-DP 8” Polished AHJ-10V-B-DP 10” Black Anodized AHJ-10V-DP 10” Polished AHJ-10VHD-DP 10” Heavy Duty AHJ-12V-B-DP 12” Gloss Black Anodized AHJ-12V-DP 12” Polished AHJ-12VHD-DP 12” Heavy Duty AHJRELAYKIT-2-DP Repl. Relay Wiring Harness Atlas Digital Position Gauge Kit Digital LED position gauge for Atlas™ Hydraulic Jack Plates. Will not t Atlas Micro-Jacker. Numbered from 0 to 20 where each number indicates 1/4” rise. All Atlas™ Jacks are pre-drilled to t. Part No. Description FAGK-1-DP Fits 4” & 8” Models, Black Face FAGK-2-DP Fits 6”, 10”, 12” & 14” Models, Black Face Part No. Description JPZ-6-DP 6” Single Adjust Jack Plate JPZ-10-DP 10” Single Adjust Jack Plate Eliminates side slippage. Matching slotted extrusions LOCK side plates in place. Made of strong aircraft grade aluminum— a full 1/2” for strength. Handles all V6 and V8 outboards up to 300 hp. Easy to adjust from top of jack. Available in various setbacks with 5” of vertical adjustment. Z-Lock™ Manual Jack Plate Tough 3/8” thick aluminum bracket provides an inexpensive solution to mounting a long shaft outboard to a short transom. Also great as a xed jack plate for all V6 outboards. Handles all outboards up to 150 hp. Three engine mounting holes on top and slot on bottom along with two transom mounting holes combined with a 3” designed lift allows a total of 5 1/2” of lift with a full four (4) inches of setback. Hi-Jacker™ Fixed Jack Plate Part No. Description JP-4FA-DP 4” Fixed Jack Plate This cast aluminum offset type jack plate is designed for clamp-on mount outboard motors up to 35 HP. The Mini Jacker™ allows mounting of long shaft motors to shorter shaft transom boats and stands off transom 4”. The engine mounting surface is 11-1/2”W x 10”H and features a vertical offset of 3”. The overall width of transom mounting anges is 17”. Super for skiffs, aluminum boats, and in atables. Mini Jacker Outboard Jack Plate Part No. Description MJ-1-DP Mini Jacker Part No. Description JP-6PW-DP 6” Adjust Jack Plate, 3/8” Thick Pro Hi-Jacker Jack Plate Adjustable Jack Plate made of high strength, 3/8” thick aluminum. One-piece design allows for top adjust, while locking bars allow one wrench adjust. Maximum 175 HP outboards. 4” vertical adjustment with 6” of setback. Bolt Kit for Jack Plates Bolt kit for mounting outboards to plate. Kit Contains: 4 each 1/2” x 2-3/4” stainless steel long bolts, 4 each 1/2” x lock nuts - brass with Nylon Insert, and 8 each 1/2” at washers - stainless steel. Part No. Description BK-1-DP Fine Thread, 1/2”-20 x 2-3/4” w/Shoulder BK-2-DP Fine Thread, 1/2"-20 x 3" Fully Threaded Part No. Description FFBT-D-DP Dual FFBT-S-DP Single FinJerfle[ Blinker 7rim Control for Hydraulic +elms FingerFlex incorporates “Positive Clicking” technology that provides positive touch and feel so, unlike similar systems, you know when your trim is operating and that’s important when you really need it! It can be installed on the right or left side of the bezel or both for dual controls. It can also be used to control hydraulic jack plates in addition to tilt and trim systems. Versions are also available to t most mechanical steering systems. Part No. Description TTC-1-DP 50 AMP 7ransom 7rim &ontrol Puts tilt and trim control anywhere. Switches feature weather-resistant design and can also operate power jack plate. Part No. Description HF-1T-DP Top Load Hot Foot The ultimate upgrade for the boater looking for safety and performance features that made Hot Foot™ the foot throttle boaters demand. HOT FOOT™ Pro sports a rugged aluminum nish with great color graphics on the pedal to accent any high performance boat. The top loading feature for the throttle cable* makes HOT FOOT™ Pro easier to install and gives more foot and leg room (requires longer throttle cable, not included). Standard features include a patented idle stop for the Ficht and Optimax engines, stainless steel return spring, Te on bushings on all critical pivot points and tow clip for added security. Drive your boat like you drive your car with improved safety and throttle control. Hot Foot™ Pro - Top Load Foot Throttle Part No. Description HF-1-DP Universal Hot Foot HFS-1-DP Hot Foot Throttle Replacement Spring Hot Foot™ Throttle Allows you to drive your boat like you do your car. You keep both hands on the wheel and control the throttle with your foot. The throttle returns to idle if you remove your foot. This throttle is a must-have for safe operation of high performance boats. Equipped with toe clip for additional safety in extreme operating conditions. Uses standard control cables for easy hook-up (longer throttle cable not included). Mounts directly to oor of boat with four screws (not included). Replacement spring for all Hot Foot™ Throttle models.
RkJQdWJsaXNoZXIy MTAyMzU3Ng==